(Image: [[https://g28carkeys.co.uk/wp-content/uploads/2023/11/key-from-new-car-2021-08-29-05-15-15-utc-min-scaled.jpg|https://g28carkeys.co.uk/wp-content/uploads/2023/11/key-from-new-car-2021-08-29-05-15-15-utc-min-scaled.jpg]])How to Change a Subaru Spare Key If you have lost your Subaru car key, you should call a locksmith. Locksmiths are usually able to cut you keys at a lower cost than the dealer. Fob remote "push to start" intelligent keys or a simple metal key are the two most commonly used types of Subaru car keys. The Fob key is equipped with an embedded chip that requires reprogramming. Keyless Entry System The key fob can be used to lock and unlock your Subaru remotely. It also opens the trunk of your vehicle or the lift gate. These remotes use keys in your car to communicate with your vehicle's computer. Subaru models offer a little well-known feature called PIN Code Access. You can utilize a personalized number sequence to start and open your car. If you have a newer Subaru Forester, Outback, Crosstrek, WRX, WRX STI, or Impreza that has this feature, make sure you check your owner's guide to find out how to utilize it. It's likely that the battery inside the key fob is dying. You can test the battery life of your key fob using an electronic tester that you can carry around or a multimeter that you have in your garage. The next step is to remove the key fob from its case and inspect its transmitter circuit board. The board will contain one or two sets of eight-digit numbers, so write down the first set so that you can remember it later. After that then put the key fob back together and you'll be ready to begin programming it at home. The procedure for programming will vary based on the type and year of your car but it's usually easy enough to complete by yourself. Key Fobs Subaru's latest models come with key fobs that can not only unlock your doors and turn on your lights, lock your gas cap, and start your vehicle. This is especially useful if been at a gas station and your car won't even start because the battery inside the key fob has died. It is likely that your [[https://telegra.ph/Whos-The-Worlds-Top-Expert-On-Subaru-Car-Key-07-20|subaru keys lost]]'s key fob, whether it's new or old it is able to be replaced. Be aware that some of the more modern models, with their advanced technology, may require visiting a dealer. With little effort and some time, you can design your own key fob replacement. Start by opening the case and inspecting the circuit board of the transmitter. (Instructions on how to open the case are usually included in the owner's manual). It should contain two or three serial numbers each of which has 8 digits long. Keep the first series of numbers in your wallet for later for reference. Then, get into the driver's seat. Close all doors. Turn the key to start your vehicle and then switch off after 10 turns. Press the lock button on your key fob and then open the door to test whether your doors work correctly. Close the door, and then remove the key. You should hear the chime from your car, signalling that the key fob has been programmed. Ignition System The key battery may be dead if your Subaru keys aren't functioning as they should. If you know how, you can replace the key fob's battery yourself. The replacement battery is inexpensive and simple to locate. If the key fob you have doesn't respond to your commands, it may be a problem with it. It's recommended to go to a dealer to obtain a spare key. They'll make sure that the key is a genuine [[https://yogaasanas.science/wiki/A_Journey_Back_In_Time_What_People_Discussed_About_Subaru_Outback_Replacement_Key_20_Years_Ago|subaru impreza Key replacement]] key that's covered by warranty. They'll also program it to your vehicle. This is much simpler and safer than getting an aftermarket key from a company online. You can also request that the dealer cut a new key if you provide them with your VIN number as well as proof of ownership. They'll use this information to code the replacement key to ensure that it will be accepted by the immobilizer. This is a more intricate process than cutting a single key, and the dealership will charge you more for it. After the new key has been programmed it will be able to switch it to your current key. It will take only five seconds to insert the new key, so make sure to keep your working keys close at the ready. You can remove the key after the security light stopped flashing and you can test it. Battery Replacement One of the most important features that makes Subaru fobs so useful is their ability to turn on your car's power windows and sunroof with a single touch of the button. However, the battery in the [[https://menwiki.men/wiki/Subaru_Replacement_Keys_Its_Not_As_Hard_As_You_Think|subaru outback key]] key fob is not designed to last forever and will eventually need to be replaced. Fortunately, changing the battery is a simple procedure that you can do yourself with the help of this quick guide from Capitol [[https://hikvisiondb.webcam/wiki/15_Funny_People_Working_In_Subaru_Key_Replacement_In_Subaru_Key_Replacement|subaru legacy replacement key]]. To begin the process, you'll have to find the small crack in the seam that divides the front and back of your key fob. It is possible to open this seam with an flat-head screwdriver to expose the small compartment that houses the battery. Insert the new battery and ensure it is facing up correctly. Remove the old one. Once everything is reassembled then you can use the new key fob to lock, unlock, and start your vehicle without difficulty! It's always an excellent idea to keep an extra set of keys in your possession especially if you've lost yours or it's not functioning properly. A new key can be bought at your local auto dealership, or you can have one cut by a locksmith. It is important to ensure that your key fob is working well as soon as possible so that you can safely drive.(Image: [[https://g28carkeys.co.uk/wp-content/uploads/2023/10/FIAT.png|https://g28carkeys.co.uk/wp-content/uploads/2023/10/FIAT.png]])